Page Index Toggle Pages: [1] 2  Send TopicPrint
Hot Topic (More than 10 Replies) Hepburn receiver finishes (Read 1160 times)
Oldman1950
Full Member
***
Offline



Posts: 134
Location: Virginia
Joined: Feb 8th, 2014
Hepburn receiver finishes
Mar 20th, 2019 at 4:45pm
Print Post  
Does anyone know if Remington Hepburn receivers and trigger guards were nickel plated from the factory?

A. J. Palik
  
Back to top
 
IP Logged
 
beltfed
Frequent Elocutionist
*****
Offline



Posts: 1054
Location: Central Wi
Joined: Dec 20th, 2007
Re: Hepburn receiver finishes
Reply #1 - Mar 20th, 2019 at 5:26pm
Print Post  
My Rem Hep has a case hardened receiver
beltfed/arnie
  
Back to top
 
IP Logged
 
Bill Lawrence
Oldtimer
*****
Offline



Posts: 858
Joined: Mar 17th, 2014
Re: Hepburn receiver finishes
Reply #2 - Mar 20th, 2019 at 6:03pm
Print Post  
As beltfed notes, the majority of Hepburn receivers were case-hardened in color.

That being said, since you could get what you paid for then and since plating was a factory option for other Remington guns, I'm sure the Hepburn could be special ordered with nickeled parts.  Whether any actually were, however, requires the knowledge of our Hepburn experts, perhaps aided by Tom Rowe's Hepburn book.

Bill Lawrence
  
Back to top
 
IP Logged
 
Old-Win
Frequent Elocutionist
*****
Offline



Posts: 1226
Location: Minnesota
Joined: Nov 24th, 2005
Re: Hepburn receiver finishes
Reply #3 - Mar 20th, 2019 at 6:17pm
Print Post  
Sometimes a case hardened receiver can fade to where it looks just like nickel.  I had a highwall that looked that way.
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 11574
Location: Oregon
Joined: Feb 2nd, 2009
Re: Hepburn receiver finishes
Reply #4 - Mar 20th, 2019 at 7:12pm
Print Post  
Never seen a nickeled Hepburn receiver, and Rowe's book only shows one and it's described as "re-nickeled". Not sure if that means nickeled afterwards, or nickel done over after it went bad? It's an engraved one, and is on page 202.
But there are thousands I haven't seen, so I suppose there is possibly an original nickel receiver out there somewhere.
  

(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Dales
Senior Forum Member
****
Offline



Posts: 266
Location: Western NY
Joined: Oct 21st, 2013
Re: Hepburn receiver finishes
Reply #5 - Mar 21st, 2019 at 9:19am
Print Post  
If you are looking at the one on Gunbroker It does not look like a factory job and the barrel looks like a modern replacement .
Dales
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 11574
Location: Oregon
Joined: Feb 2nd, 2009
Re: Hepburn receiver finishes
Reply #6 - Mar 21st, 2019 at 10:05am
Print Post  
Dales wrote on Mar 21st, 2019 at 9:19am:
If you are looking at the one on Gunbroker It does not look like a factory job and the barrel looks like a modern replacement .
Dales


Not only not factory, but not well done. They nickeled all the screws, which Remington would likely have left them blued. And I wonder if the seller just stuffed that front sight on it? It's way off center to the left, and appears to be a last minute install.
  

(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
ssrifles
Junior Forum Member
**
Offline



Posts: 78
Joined: Mar 23rd, 2009
Re: Hepburn receiver finishes
Reply #7 - Mar 21st, 2019 at 10:21am
Print Post  
when the research was being done for the hepburn book.i knew and had seen 3 and there was 1 more known, so 3 or maybe 4.2 were engraved 1 was a very nice finished special order not sure of the 4th.very rare    tony <><
  
Back to top
 
IP Logged
 
Oldman1950
Full Member
***
Offline



Posts: 134
Location: Virginia
Joined: Feb 8th, 2014
Re: Hepburn receiver finishes
Reply #8 - Mar 21st, 2019 at 4:16pm
Print Post  
I was looking at the Hepburn on Gun Broker.
"REMINGTON HEPBURN No. 3 38 55 WIN CUSTOM GUN"
I sent the seller an email asking the distance between the scope blocks---length of pull and the condition of the set triggers.
The seller responded:
7.25 inches on the scope blocks
Length of pull 13.25 to front trigger
Set triggers function perfectly

I already have a Hepburn in 32-40 but once you get the Hepburn bug............

I think I will pass on it but if the hammer price is low enough it should make a good shooter for someone.

I also noticed that the rear sight appears to have been repaired at some point.

A. J. Palik
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 11574
Location: Oregon
Joined: Feb 2nd, 2009
Re: Hepburn receiver finishes
Reply #9 - Mar 21st, 2019 at 8:35pm
Print Post  
I noticed what looked like some welding on the base of the staff too. Wasn't sure if it was a repair, or if the staff was shortened?
Not sure whose tang sight it is either, but not a Remington. Maybe a Lee Shaver? If so he had some issues early on with soft solder and staffs came off. I bought one with the staff broken off for cheap, and sent it to him to be fixed. He silver soldered it on, and can't tell it was ever broken now.
  

(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
40-82Hepburn
Oldtimer
*****
Offline



Posts: 757
Location: new jersey
Joined: Feb 18th, 2008
Re: Hepburn receiver finishes
Reply #10 - Mar 22nd, 2019 at 8:05am
Print Post  
I looked at the pics in the GB listing and to my old eyes the receiver looked to be in the white. Reminds me of two Ballards that I have. The case coloring is gone, leaving a silvery, almost nickel plated appearance. Could the case coloring have been polished off ?
  
Back to top
 
IP Logged
 
Bill Lawrence
Oldtimer
*****
Offline



Posts: 858
Joined: Mar 17th, 2014
Re: Hepburn receiver finishes
Reply #11 - Mar 22nd, 2019 at 9:22am
Print Post  
The receiver and the buttplate finish match and to me have the even matte look of an electroless nickel coating.  For contrast, compare the buttplate on the subject's rifle to that of the $6500 Hepburn that's also on gunbroker, the latter almost surely being factory.

Bill Lawrence
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 11574
Location: Oregon
Joined: Feb 2nd, 2009
Re: Hepburn receiver finishes
Reply #12 - Mar 22nd, 2019 at 11:01am
Print Post  
I have had a few casehardened receivers that had turned that "nickel" look with age, but none looked like that Hepburn. I think the Hepburn is truly a nickel plate, but I'm still unsure it's original to the gun.
Hope someone like Tony who has seen these could comment on the nickel, and the nickel plated screws? The finish just looks somewhat flat compared to nickeled guns I've seen from that era.
  

(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Kurt_701
Oldtimer
*****
Offline



Posts: 800
Location: Missouri
Joined: May 20th, 2004
Re: Hepburn receiver finishes
Reply #13 - Mar 22nd, 2019 at 1:02pm
Print Post  
Could the finish be Metaloy Hard Chrome plating? Similar to this pistol.
  

M-14 3rd Battalion 27th Marines RVN 68'69'
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 11574
Location: Oregon
Joined: Feb 2nd, 2009
Re: Hepburn receiver finishes
Reply #14 - Mar 22nd, 2019 at 3:34pm
Print Post  
Sure does look a lot like that hard chromed pistol!
  

(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Page Index Toggle Pages: [1] 2 
Send TopicPrint